5. Configure IP addresses for the router’s iSCSI ports by entering an IP address:

• In mpx Manager, modify the iSCSI Port Information page.

• In the CLI, issue the set iscsi command (see“set iscsi” (page 110).

To configure the local router and chassis:

1. Take these preliminary steps:

a. Ensure that the local router and chassis have access to the source array.

b. Ensure that the LUNs are visible.

c. Create a data management LUN , see “Creating and removing a DML” (page 69).

d. Configure any potential migration jobs using the destination array (local).

e. If the destination array was initially present at the local site and then moved to a remote

site after the initial copy, ensure that the migration jobs are in a COPY COMPLETE state.

2. Assign IP addresses to the routers iSCSI ports by issuing the set iscsi command , see “set

iscsi” (page 110).

3. Ensure IP connectivity between the routers by checking for the following:

• The local router’s MGMT. port can ping the remote router’s MGMT. port.

• The local router’s network ports can ping the remote router’s iSCSI ports.

4. On each local router blade and chassis, issue the remotepeer add command, for details

see “remotepeer” (page 101), and then specify the management port of the remote router. This

step ensures that the remote router has access to the destination array ports and can

communicate using the specified Ethernet ports.

HP recommends the following connections:

• Blade 1 of the local chassis establishes as the peer Blade 1 of the remote chassis.

• Blade 2 of the local chassis establishes as the peer Blade 2 of the remote chassis.

5. Validate the configuration by executing the show remotepeers command, see “show

remotepeers” (page 132).

6. On each blade, issue the array import command, see “array” (page 77), and then specify

the array to be imported. The imported array is automatically marked as a destination array.

7. Ensure that the array has been imported successfully by issuing the show array command,

see “show array” (page 112), and then validating the LUN information.

Each blade should see all of the paths that are available on the peer. However, only the paths

that are online on the peer are online locally.

Adding a Migration Job and resuming an existing Migration Job

You can add a remote migration job using an imported array. You can also enable and disable

compression for the migration job.

If a remote migration job was previously running and the array comes online with the LUNs involved

in the migration, the migration job automatically resumes operation.

For an example of using Native IP to add a remote peer, see “remotepeer” (page 101).

To remove an imported array, see “Removing an offline array” (page 69).

Native IP remote migration firewall ports

With Native IP remote migration it may be necessary to open specific ports if a firewall is used in

the network. Table 6 (page 32) describes the ports that are needed to communicate with the MPX

from the mpx management GUI as well as native IP communications between the local and remote

MPX.

Online remote migration 31

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 179 180

Commenti su questo manuale

Nessun commento

AcuRite 00734 Thermometer manuels

Manuels d'utilisation et guides de l'utilisateur pour Thermomètres AcuRite 00734 Thermometer.
Nous fournissons des manuels en pdf 1 AcuRite 00734 Thermometer à télécharger gratuitement par type de document : Manuel de l'utilisateur

Acurite 00734 Thermometer Manuel de l'utilisateur (1 pages)

marque: Acurite | Catégorie: Thermometers | Taille: 0.14 MB |

Table des matières

INSTRUCTION MANUAL

Plus de produits et de manuels pour Thermomètres AcuRite

Modèles	Type de document
01036 Weather Station	Manuel de l'utilisateur AcuRite 01036 Weather Station User Manual, 26 pages
00425 Themometer	Manuel de l'utilisateur AcuRite 00425 Themometer User Manual, 10 pages
01033 Weather Station	Manuel de l'utilisateur AcuRite 01033 Weather Station User Manual, 5 pages
03118 Thermometer	Manuel de l'utilisateur AcuRite 03118 Thermometer User Manual, 1 pages
00615 Weather Station	Manuel de l'utilisateur AcuRite 00615 Weather Station User Manual, 18 pages
03128 Thermometer	Manuel de l'utilisateur AcuRite 03128 Thermometer User Manual, 1 pages
00973 Weather Station	Manuel de l'utilisateur AcuRite 00973 Weather Station User Manual, 5 pages
02001A1 Weather Station	Manuel de l'utilisateur AcuRite 02001A1 Weather Station User Manual, 12 pages
00739 Sensor	Manuel de l'utilisateur AcuRite 00739 Sensor User Manual, 1 pages
00288E Thermometer	Manuel de l'utilisateur AcuRite 00288E Thermometer User Manual, 1 pages
00250 Weather Station	Manuel de l'utilisateur AcuRite 00250 Weather Station User Manual, 13 pages
00754 Thermometer	Manuel de l'utilisateur AcuRite 00754 Thermometer User Manual, 1 pages
75110 Weather Station	Manuel de l'utilisateur AcuRite 75110 Weather Station User Manual, 9 pages

Qlogic MPX200 Guida Utente Pagina 31

Commenti su questo manuale

Prodotti e manuali riguardandi Software Qlogic MPX200

AcuRite 00734 Thermometer manuels

Acurite 00734 Thermometer Manuel de l'utilisateur (1 pages)

Table des matières

Plus de produits et de manuels pour Thermomètres AcuRite